Fence Repair — Replacing a Broken Fence Post

Handyman Atlanta

It may sound just like a daunting task to replace a damaged fence post however it is not as difficult as it can certainly seem. It can have a little hard work and a few simple tools you almost certainly have inside the shed or garage. Where does one start? First you need to assess the project and the damage. Did the post rot and just break or was it sheered off as a result of some nasty weather conditions. Perhaps there is still a remaining stump or perhaps is it broken off with the ground or concrete level? Try not to be afraid, the project is moderately difficult and really should just take about One or two hours of your energy to perform and your fence is going to be terrific once again.
Atlanta Handyman

Difficulty Level: Moderate

Time Required: Approximately 1 to 2 Hours

Required Tools

- Shovel

- Pry Bar

- Level

- 1 Replacement Post — Typically 4" x 4" x 8' Cedar or Treated Lumber

- 1–80 Pound Bag of Quickrete Concrete Mix

- 3" Wood Screws (Approximately 12 Screws)

Optional Tools

- Auger or Clam Shell Post Hole Digger

- Bag of Gravel

- Hand Saw or Circular Saw

Typically, most fence posts are set into the ground using concrete but other people installed using packed dirt inside the fence post hole. If you do not see concrete on the walk-out, take a typical shovel and dig down a few inches near the broken post location and find out in the event you hit concrete. Most fence posts are placed in concrete but for the greater degree a standard post hole is roughly eight (8") to twelve (12") inches in diameter and most are about twenty-four (24") inches deep.

There are different schools of thought with regards to removing a preexisting post. A lot of people choose to smash and grab technique which is simply utilizing a hammer and chisel or pry bar to break the concrete into small pieces and pull them from the existing hole one after the other. The process does work but is much work therefore it may take between one (1) and two (2) hours at work to extract the concrete from the hole. It’s fine if you have an individual post to replace but when you can find multiple, the project involved is incredibly tedious and tiring and you will find good ways.

The process I favor would be to take a long, skinny bladed shovel and seek out the dirt in order to the inside in the concrete exposing along side it in the concrete block. Just be sure you pile the dirt near the hole since the dirt you remove will be employed to re-pack the outlet after the post and concrete block is taken off from your ground. From your regarding the concrete, find out about six (6") to eight (8") inches and down twenty-four (24") inches. This allows for a pocket as wide because concrete block. If the piece or stump through the existing post is still available, countless uses for flash and initiate moving the concrete block forward and backward while using new pocket space you just created. Once it can be loose, you have to be able to utilize your shovel or pry bar as being a lever and lift the concrete block from the hole. Take care and make certain you lift using your legs since the concrete block can weigh around eighty (80) pounds. If your existing post or post stump has stopped being connected to the concrete, you ought to be able to use a pry bar as well as your shovel to move the current concrete block backwards and forwards in a similar manner loosening it from its original placement. Once, the block is movable, utilize the same process as stated before but please be careful to use proper lifting techniques when taking out the concrete. A doctors visit just isn’t prescribed with this project.

As soon as the block is slowly removed, use the dirt you taken off the excavation to complete the six (6") to eight (8") inches you originally dug out. Make sure to pack the dirt solidly because it will provide the lateral support to the new post if it’s available. The concrete you have once you set the modern post will give you a lot of support along with attaching the present fence structure nevertheless the better you pack the dirt, the greater the actual result. You ought to be using an ordinary hole approximately twenty-four (24") inches deep and approximately eight (8") to 12 (12") inches wide.

From here, you should take your clam digger or post hole digger or you would not have one, don’t use anything but your shovel and find out approximately two (2") inches at the bottom of the hole. Then add loose gravel in those two (2") inches for drainage to help keep water from the bottom of the post. If you do not have or did not purchase a bag of gravel once you purchased your replacement post and concrete, do not concern yourself. The concrete has gravel in it and definately will work however the gravel does make the drainage more effective. Once you’ve the camp available, it’s install the replacement post.

Grab your replacement post and center it within the hole. If you have a helper, keep these things retain the post and make sure who’s lines up correctly using the fence and the old post you just removed. Once you’ve it in the correct position, open an eighty (80) pound bag of Quickrete concrete and pour it dry into the hole. Remember to be wearing eye protection and cover orally and that means you do not inhale the concrete dust that typically spews from the hole because you pour in the mixture. Pour all the contents into the hole. Grab your backyard hose or even a bucket water and initiate pouring water into the hole and make certain to pour around the new post within a circular pattern to actually have the whole top layer with the concrete wet. The river will quickly bubble mainly because it starts seeping for the bottom. Still add water until it pools a bit. It’s going to absorb over the mix. Now, take your pry bar or perhaps a bit of rebar or even a sturdy stick and start poking the concrete mixture to aid receive the water to flow down to the bottom as well as get rid of the air bubbles that form. It’s OK if the water pools a little along with result in the mixture too wet because it will need longer to create.

Now take your level and ensure how the post remains in the upright vertical position. It is helpful if you check into multiple sides and ensure the bubble for the level is incorporated in the middle and between the marks. Once the post is level, use items of wood to create a stand of sorts at the bottom to keep the post motionless whilst the concrete creates overnight. The concrete will begin setting and with regards to the climate needs to be ready in the morning to re-hang fences pieces. If your post moves, wiggle it in to the vertical position after which utilizing your stick or pry bar, slowly move the concrete mix around in order that it touches the post on the sides on your lawn without any gaps. If gaps form, you may have to put in a amount of additional water to really make the mixture more liquid. Any pooled water will probably be distributed around the concrete and surrounding dirt and in addition evaporate as the concrete sets.

In the morning, you ought to be capable to re-affix a gate for the post and yes it should be good as new. Prior to deciding to attach the previous fence pieces, you can examine the height from the fence post as compared to the other posts within your fence line. With regards to the rest of your fence, you might want to work with a hand or electric saw to reduce the new post to check the opposite posts in your fence. When the post doesn’t need to be slashed, you’ll be able to attach that old fence pieces to the new post. Make sure you use screws if you attach fences it into the new post to ensure a far more stable connection than nails which can grab in windy or rainwater conditions with time causing integrity issues.

Like what you read? Give DeckStaining777 a round of applause.

From a quick cheer to a standing ovation, clap to show how much you enjoyed this story.