How to make a nut slot

7 min readOct 19, 2022

How To File The Nut Slots On Your Acoustic Guitar — FuelRocks.

The nut with the slots for strings is showing in the following picture. The slots are very deep. It looks weird…. Perhaps a previous player has deepened the slots to make it easier to fret at that end of the fingerboard. As long as the strings don’t rattle or buzz on the lower few frets, it’ll be fine. If you really want to file some off the. Starting with the lowest string, insert the round file into the nut slot and file downwards, towards the headstock. Be careful not to file too deeply! 4. Test the fit of the string in the slot. It should be snug but not too tight. If it’s too tight, file a little more; if it’s too loose, stop filing. 5. Repeat steps 3–4 for the remaining. Most of the books tell you to cut the slot a little at a time, with a few strokes of the nut file, You cut a little bit, re-fit the string, measure the clearance, unmount the string, cut a little bit, re-fit the string, and so on until one of two things happen: You get to where the string height is perfect, and proceed to the next string, or.

10 Steps to Making a New Replacement Nut For Your Guitar.

Roughly shape the nut. The top of the nut will be shaped to follow the radius of the fretboard. As a starting point, place the blank in the slot and trace the shape of the fretboard onto it. To determine the height of the nut, add the height of the frets to this traced line, then add an additional.030" for string clearance (the space from the. Sep 03, 2019 · The basic idea when slotting your nut is file the slots as low as possible (or to the players personal preference) without going too low and creating any buzz. You also want to consider filing the correct width of each slot, the angle and the spacing between slots. Other factors to consider are the tools at your disposal and the type and material of the nut itself.

Nut Slot Depth Anyone Can Do — YouTube.

Jul 10, 2010 · Fill the slot with baking soda (some suggest bone dust, but baking soda works just fine). 2. Carefully apply some thin CA (super glue). It’ll quickly wick into the baking soda, making it very hard. 3. Allow the glue to dry a few minutes. Length will depend on how old the glue is. 4. Once dry, file slot as you normally would. Rough-cutting Nut String Slots. We left our nut with the slot positions marked on top. Great. You’ll remember I’d also used the half-pencil to mark the fret height on the front face of the nut. That fret height line is my final destination but, right now, I’m going to use it as an indicator for my rough slot-cutting. Apr 23, 2020 · Elyse walks you through every detail you need to know to make your own perfect guitar nut from a blank. From removing the old nut, cleaning the nut slot, cutting and sanding, identifying and marking string spacing, proper slotting techniques, polishing the nut to get a jewel-like finish and finally installing the nut.

How To | Filing the Guitar Nut | Fender — YouTube.

One of the most delicate tasks in fashioning, repairing or replacing a guitar nut is creating evenly filed slots. Fortunately, genuine Fender replacement nu. Jan 02, 2019 · You simply tape off the ends of the nut and then remove a small portion of the cloth and roll it up, then insert it into the slot that is too low. Then flow a thin super glue into the fibers using a thin whip tip. You can find thin super glue with whip tips on (the part number is #0010). You can either drop super glue accelerator on. 0. File the nut’s front edge at a 45-degree angle to the rear edge of the file so that the string will have appropriate downward pressure. The real point of contact between the string and the nut should be at the front of the nut in order to play effectively in tune (the fretboard side). When playing guitars with slanted headstocks, make sure.

Decreasing Nut Slot Depth | The Gear Page.

Jan 10, 2017 · A vice, five gauged nut slotting files, and the nut itself. Below: The nut secured in the vice. Below: A.130" file was used for the 5-string B, seen at left of nut. Note that this is not filed to final depth; this will not be doneBelow: The items used in this build step. A vice, five gauged nut slotting files, and the nut itself. May 11, 2008 · Just make another nut and slow down this time. Get the blank to dry fit the slot and lay flat. Trace the first fret contour on the blank using a flattened pencil or scribe. Take the nut out and cut the top to match the radius PLUS 1/16 inch or so. Put it back with Titebond glue and cut your slots just to the traced line and you will be close.

Make your own nut slotting saw | Telecaster Guitar Forum.

After adjusting the truss rod and setting the string saddle heights at the bridge, you can now make the third adjustment, which is to the nut slots. Dave Joh.

Five Factors That Make a Good Guitar Nut — zZounds Music Blog.

To make the gauge strip into a saw, I placed the strip in a bench vise with about 0.020" of the edge above the top surface of the vise. Then, using a small, very sharp cold chisel, I lightly tapped the chisel into the edge of the gauge strip at an angle, raising a small burr each time that would act as a saw tooth. I first use a file, then some medium grit sandpaper to remove file marks and belt sander scratches, and finally polish it with a finger nail buffer. Then I glue it into the nut slot (just a tiny dab of glue is all that’s necessary), touch up the nut slots, and polish the nut slots with a fine grit sandpaper to keep the strings from catching.

Manufacturer of.

With bone you have to carefully saw off a little sliver and glue it into the slot, maybe even filing the slot out square to make the “graft” fit. the better choice than all this is to pop the nut out and shim it up from the bottom, then re-cut all the slots to the right height again. 202dy likes this.

How do I deepen a nut slot? How deep? — Telecaster Guitar Forum.

Mar 16, 2020 · When to adjust the nut slots. You typically make adjustments to the nut after setting the bridge, as the heights of the nut slots are a function of the overall string angle. The string angle is determined by the string action height at the bridge. The individual slot depths are cut so each string can clear the first fret. Another DIY hint……..If you know how much clearance you want above the first fret, simply select the appropriate blades on a set of feeler gauges and strap the gauges tightly on the neck next to the nut with rubber file away until you hit the gauge….. Apr-18–2013, 3:47pm #6 Jim Garber Mando-Accumulator Join Date Mar 2003.

Raising a Nut Slot — Guitar Setup and Maintenance — YouTube.

Step 4: File the slots. For good string positioning, mark the location of the two E strings from your old nut on a piece of tape. Match these positions to marks on the string spacing rule, and it will locate the rest of the string slots for you. Mark the string locations on your nut blank and place it in the slot, held in place with your two E.

How to Make a Guitar Nut from a Blank — StewMac.

Tighten the Safe Slot to hold the shim against the nut (again, do not over-tighten). Strike a line on the nut. Shape the top of the nut. Use a file or a belt sander to lower the top of the nut to the top of your pencil line. Leave the line showing, so you have a little extra to work with as you cut the nut slots. Oct 07, 2019 · Getting the bottom cut to shape will allow your blank to sit perfectly in the slot and is important before proceeding. Actually, on that subject, pay close attention to the nut’s fit in the bottom of the slot. Make sure the nut sits nice and flush at the bottom. Marking out the nut blank.

Tech Tip: Filling and Recutting the Nut Slot | Musicians.

Here are some tips for cutting the string slots in a guitar nut.Notched Straight Edge: Files: Action. There are tricks to raising nut slots, but if you are really doing an ideal job the only way to “go back” is to start over making a completely new nut. 4. String Angle. The next consideration when making an ideal nut is the angle the bottom of the string makes when passing from the fretboard to the headstock.

Making a Guitar Nut — 3 Tips for Proper Slotting — YouTube.

The best nut-making material: Bone for Tone! Trade Secrets. Plastic nuts are high-speed and low-cost!… Product Instructions. Slotted Bone Nuts Sizing Sheet. Product Instructions. Using Feeler Gauges to Control Nut Slot Depth. Product Instructions. Making a Nut, Step-by-Step. Product Instructions. Graph Tech Instructions. Shop. New Items.