How to Make Stainless Steel Chain Jewelry: The Simplest, Easiest DIY Project!: stainless steel chain jewelry making
Image Source: Freepik
For years, the only jewelry made out of stainless steel was the kind that you should probably keep in your pocket. It’s a durable metal, but it’s not prone to oxidation, so it’s perfect for anything that you want to wear for a long time without tarnishing. We’re not talking about watches and bracelets here — this is DIY chain jewelry, and it’s one of the simplest ways to start wearing stainless steel. The beauty of using this type of metal is that it suits a variety of looks, from simple and elegant to flashy and bold. The process of making it is simple, too. You don’t need any fancy tools or special knowledge to get started. You just need a few basic supplies and a little time. To get you started on your own DIY project, we’ve rounded up everything you need to know about making your own stainless steel jewelry.
What materials do you need to make stainless steel chain jewelry?
You can find stainless steel chain at jewelry supply stores, but you can also make it yourself. To do this, you will need a few basic supplies: — A pen for marking — An abrasive wheel or file for removing excess metal — Round nose pliers — Flat nose pliers — Wire cutters — Stainless steel wire (about 24 gauge) — Jewelry clasp with jump rings (optional) The first step is to measure the length of the chain in inches that you want to end up with. The number of links in a length of wire is equal to one inch. This means that if you want your chain to be 18 inches long, you’ll need 36 links of wire. To figure out how many links of wire to cut, divide the total by two. In this case, it would be 18/2 = 9. You should now have six pieces of wire measuring 9 inches each. Next, use your round nose pliers and a pen to mark nine spots along each piece of wire where you want a link to go — three on each side, so there are three sets of two links next to each other and four single links in between those sets. Once you’ve marked all nine spots, use your flat nose pliers to bend the ends together at each spot where there are two links next to each other so they touch (see diagram below). It’s important that as
What tools will you need to make stainless steel chain jewelry?
The tools you’ll need for this project depend on what type of finish you want to achieve. If you want a polished, silky look, then you’ll need: — Wire cutters — A round nose pliers — A file or coarse sandpaper — A bench pin and anvil (optional) If you want a rough and raw look, then you’ll need: — Wire cutters — A chain nose pliers — A large metal can with a lid that has been washed out thoroughly (canned goods are great for this) — A bench pin and anvil (optional) **Warning: Please be aware that there is a fire hazard if the metal can is not washed out properly.**
How to make stainless steel chain jewelry: the basics
All you need are a few things from the hardware store and some basic jewelry-making skills to make your very own chain jewelry, which can be made out of any type of metal. The first step to making this type of jewelry is selecting the right size of chain. You’ll want it to be long enough so that you can tie a knot with the ends (or close it up in a clasp) but not so long that it drags on the ground or hangs too low. If you want to get really creative and have a little bit more fun with your design, you can use different lengths of chain for each piece. You will also need jump rings to attach the links together and a clasp to secure them at the end. The size and shape of these pieces depends entirely on what you’re using them for. If you’re making very delicate jewelry, for example, you might want tiny jump rings and clasps that are easy to wear. There are two ways that these components can be attached: either by heating them up with a torch or by hammering them closed with another piece of metal. You’ll want to solder together any links that are an odd length and hammer closed any jump rings that don’t look like they have a nice, round shape when they’re hanging open in their original position. The final step is adding embellishments like charms, beads and charms as desired. Your creativity is
How to make a stainless steel ring
The first step is to get a stainless steel ring blank. The easiest way to do this is to find one that’s been cut from a larger piece of stainless steel, but you can also buy or cut your own. You should be able to find rings in all standard size ranges at most big box craft stores. Next, choose your desired shape, size, and thickness for your ring. When shaping the ring, be sure not to overly distort the metal and give it an oval shape rather than a round one. If you don’t have any tools handy, you can use something heavy like a hammer or some books to flatten out the edges. Then measure the inside diameter of the ring and cut off any excess metal on either side. Now you need to file down any rough edges on the inside surface with a fine-grit sandpaper so that it’s smooth against your skin. Finally, buff down the whole thing with some steel wool to get rid of all scratches and fingerprints before polishing it up with metal polish and jewelry cleaner (both available at most craft stores). Now you just need to add some beads!
How to make a stainless steel bracelet
To make a stainless steel bracelet, you’ll need: • The chain. This can be anything from ball chain to flat curb chain. The links should be the same thickness throughout. • Jump rings. These are used to connect the ends of your chain together and can be found in most jewelry-making sections of craft stores. • Lobster clasp or magnetic clasp. You’ll need one for each end of the bracelet, so two total. You can also use wire clamps for an edgier look, but they’re a little more difficult to use than clasps because you have to thread them onto your chain with pliers. • A pair of wire cutters for cutting all your chains and jump rings
How to make a stainless steel necklace
To make a necklace, all you need is a length of chain, jump rings, and a clasp. The links in the chain can be made from any type of material — I like to use a mix of silver and gold for mine. Start by opening your jump ring with your pliers. Slip the jump ring over one end of the chain and close it back up. Repeat this process until you’ve reached the desired length for your necklace. Use another jump ring to attach your clasp to the end of your chain. If you have clasps that are too small to accommodate a jump ring, you can use one of those instead.
