Stretch Wrapping Glossary
Banding is the act of applying multiple wraps of stretch film to a certain area of a load to reinforce and/or unitize a number of layers or products.
BFR — Conveyor
Between Frame Rails: The distance between the (2) outside frames on a conveyor section. Sometimes referred to as effective BFR, which would represent the usable width of the conveying surface.
Blown Stretch Film
A film extruded by the blown (balloon type inflation) system. Typically blown film is a tougher but noisier film than cast films.
The revolutions of film applied by a stretch wrapping system to the lower layers of a pallet or load. Typically more than one revolution is applied to this area to increase the load stability of the unitized load.
A mechanical roller that provides a resistive force that reduces the film feed rate being supplied to the load. The resulting “drag” will create an increase in tension between the load and the stretch film roll.
Molten plastic extruded over full width of a die, then cooled and crystallized over a drum. Cast film typically is quieter, more transparent, and glossier than blown film because of this process.
Cling (single side — two sided — differential)
Cling is a bonding agent added to stretch film to increase the stickiness quality of the film. This is desirable to allow the layers of stretch film applied to bond to the previous layers effectively creating a single wall of stretch film. Depending on the desired effect the bonding agent is applied to one or both sides. It is most commonly applied using co-extrusion where the bonding agent is a layer that is co-extruded during the manufacturing process.
Cold Rolled Steel.
Dancer Bar (Dancer Arm)
Is a pivoting roller that measures the film feed requirements of the pallet. As the pallet rotates, the stretch film needs to accelerate and decelerate around the corners to maintain a constant film force (or tension) on the load. The dancer bar pivots as the load demands more or less film fed. This is one common method by many manufacturers to measure this film feed requirement.
Erasable Programmable Read-Only Memory: An electronic device “chip” that provides a means for storage and communication for a microprocessor program associated with the PLC.
As a film is applied to a load the speed or velocity at which it is applied is called film feed. The feeding of the film is rarely constant as it must be accelerated and decelerated to compensate for the corners of the load to keep the film tension constant. Without this corner compensation feedback the film tension would increase as at the corners causing potential damage or film breakage issues.
Film Force (Film Tension)
Film Force is the retaining force applied by the stretch film on the product being wrapped. This force is typically measured in pounds. Film force is created two ways. The second method is by delaying the film feeding out of the carriage. During wrapping the film is fed out at a constant tension. By delaying the response (speed) of the carriage film feed, you electronically increase the film tension. A film force dial is typically located on the control panel or carriage.
Film Force Release
A feature typically used on automatic stretch wrapping equipment whereby the film force feature is disabled for a time at the beginning and end of the cycle. This feature prevents unwanted tension at the two points during the cycle where added tension would create problems. The stretch film pulling out of the clamp at the beginning of the cycle and the detaching of the trailing tail at the end of the cycle are typically remedied by film force release.
Is the imperial measurement used for measuring film thickness.
Film memory is THE key reason for pre-stretching stretch film. Pre-stretching stretch film creates a memory in the film, which causes a continuous elastic effect as the film tries to return to its unstretched self. This ensures that the load integrity is maintained even as the load shifts or settles during transit. It is this film memory that differentiates pre-stretched film from non-pre-stretched film or other means of unitizing. For instance, settling that occurs during shipment can loosen other methods of unitizing (strapping) where pre-stretched film memory takes up the slack and continues to secure the load.
The film tail is the stretch film end piece that is applied to a pallet or load to start a wrapping cycle. It is also the stretch wrap end piece created when cutting the film at the end of the wrapping cycle.
Stretch film designed to be post stretched or tensioned stretched by personnel without equipment is called hand wrap. Typically hand wrap does not have the stretching abilities of machine wrap and is wound on smaller and lighter rolls for easier manipulation.
Home position is the position of all the moving sub assemblies on a stretch wrapping machine when they are at rest and ready to begin a new cycle.
Idler rollers are used to bias the stretch film direction as it travels through the pre-stretch carriage. In some cases it is to ensure that the stretch film is maintained against the pre-stretch rollers to prevent the film from slipping by the pre-stretch roller.
Load Types — A-load, B-Load, C-Load
Stretch film and machine manufacturers have divided the types of loads wrapped into three load types based on the degree of difficulty to wrap the load or product.
A-Load: Is the simplest of the load types. Usually a std. pallet with no sharp edges, clean sides without obstructions that may interfere with the application of the stretch film
B-Load: This load type may have
C-Load: The most difficult type of load. It may be unstable, with sharp corners that may have an effect on speed
Is the measurement of a pallet or product load across the diagonally opposite corners. This dimension is critical in determining the overall size of a stretch wrapper. The difference in this dimension in the largest load to be wrapped and the smallest can also affect how the machine needs to be designed. The equation for determining a load diagonal of any pallet is /(L2 + W2).
Is the metric measurement used for measuring stretch film thickness.
As film is stretched there is a tendency for the film to narrow (similar to bubble gum). This narrowing of the film is called neckdown. Neckdown reduces the coverage a revolution of stretch film provides thus potentially increasing the number of revolutions required to wrap a pallet or load. The larger the distance between the two rollers stretching the film (Primary & Secondary pre-stretch rollers) the larger the neckdown.
National Electrical Manufacturers Association: An association that rates electrical devices for uses in various environments. Eg. NEMA 12 rated devices are intended for in-door use and provide a degree of protection from circulating dust and dripping non-corrosive liquids. NEMA 4 rated device are intended for indoor/outdoor use and provide a degree of protection from blowing dust and splashing non-corrosive fluids.
As stretch film is applied to a load the stretch film is typically applied so that the next layer of stretch film is applied over the previous layer. This overlapping of film layers increases load retention. By slowing the vertical movement of the stretch film carriage the larger the overlap created.
Is the amount of stretch film applied over the top of the load. As the stretch film reaches the top of the load, the vertical movement of the carriage can continue so that the film angles over the top of the load. The stretch film on top creates a downward force on the pallet load. This is also used when a plastic top sheet or corrugated top cap is applied on the top of the load to lock them in place.
Programmable Logic Controller: An electronic microprocessor device that stores and executes automatically a series of programmed commands that produce a machines sequence of operation.
Poststretch (See Tension Stretch)
Pre-stretch is the process of stretching the film in a pre-stretch carriage PRIOR to (Pre-) applying it to the load to be wrapped. As the stretch film passes through the carriage it threads past two rubber rollers (Primary roller & Secondary roller). The secondary roller is usually larger than the primary roller and its rotational speed is geared to be faster than the primary roller. This differential of speed where the secondary roller is pulling the film from the primary roller causes the film to stretch between the two, thus pre-stretching the film between one and the other.
Is the assembly n a stretch wrapper that stretches the film prior to applying it to the load. Located on a vertical traveling slide, the pre-stretch carriage applies a spiraling layer of stretch film to the load thus encapsulating the load in stretch film.
Is one of two rubberized rollers located in the pre-stretch carriage used to create pre-stretched film. The primary roller is the first rubberized roller the film passes by and is usually the smaller of the two. Its speed is also geared slower than the secondary roller.
Gathering the full width of the film using a bar or roller so that it creates a “rope” is called roping. Stretch film that has been roped is nearly unbreakable and is most often used to lock a pallet to the product. This is easily done with a turntable style machine. With rotary arm style machines an air cylinder can be used to actuate the roping process. In some cases, roping has eliminated the need for other packaging materials such as strapping.
SCR — Motor Control Board
Silicon Controlled Rectifier: A means of controlling a DC motor’s rotation speed.
Is one of two rubberized rollers located in the pre-stretch carriage used to create pre-stretched film. The secondary roller is the second rubberized roller the film passes by and is usually the larger of the two. Its speed is also geared faster than the primary roller.
Tension stretch (or post stretch) is the method of stretching the film by pulling (or tensioning) while the film is applied to the pallet. Although this increases the film force, the load being wrapped limits this tension. Empty PET bottles or light boxes will be crushed or damaged by high-tension stretch. Layers of product can be swept of a pallet and film breaks also increase as the tension stretch is increased.
Top Sheet Dispenser
Top sheet dispenser is a piece of equipment that applies a poly sheet of plastic top sheet to the top of a load to provide a water resistant layer. Typically, once applied, a top sheet is subsequently wrapped with stretch film to secure it in place. The top sheet film is unrolled, cut to size, and applied to the load automatically by the top sheet dispenser.
Top Sheet Film
Is the poly plastic film that is applied to the top of the load
Top wraps are the extra revolutions of stretch film applied to the top portion of the load to be wrapped. As the top layers are susceptible to shifting in transit extra layers of stretch film (top wraps) is applied. These extra revolutions are typically set using the top wrap counter located on the control panel.
Ultra High Molecular Weight: A type of plastic commonly used in applications where a linear bearing between sliding assemblies is required. Low wear and reduced friction properties make this a commonly used product in stretch wrap equipment.
VFD — Variable Frequency Drive
A device used to provide full control of an AC motors shaft rotation speeds. VFD’s offer a wider range of features as seen on SCR DC motor control board (see SCR). Features include, display diagnostics, multiple step speed control features and fully reset-able from voltage problems such as power surges.
Wrap parameters are the variable settings on a stretch wrapping system that can be adjusted to meet the load retention requirements of the product to be wrapped. These parameters typically include settings like: Top wraps, bottom wraps, film carriage vertical speed, turntable (or arm rotation) speed, and film force.