Completed Bridesmaid Bouquet — Photo by Sandra Costello

Make Your Own Paper Bouquet

From prototype to final product, here’s the recipe for making a paper rose bouquet.

Supplies for a Single Bouquet:

  • One 6 inch green styrofoam ball (found in the floral dept)
  • 3 chopsticks
  • Generous pile of hot glue sticks
  • 1 Green 4oz. pack of Crayola Model Magic
  • Elmers glue
  • Small dish filled with 1–2 tablespoons of water
  • 1 inch paint brush (cheap is great)
  • 2 sheets of base color tissue paper (standard gift stuff)
  • 20+ paper roses in varying size and color
  • Ribbon to wrap the “stems”
  • Long knife
  • Dustbuster
  • Tall vase or bottle
  • Optional: 1 package of Large Pearl Beads, Assorted Sizes

Instructions:

1. Using the longest knife you own, sliver off about 1.5 inches of foam to create a flat base for where the hands can rest. PLEASE NOTE! This is going to get messy. Get that dustbuster charged up and ready to suck up all the styrofoam crumbs.

2. Mark the center of the flat side of the styrofoam ball. Making a triangle, stick each chopstick in at an angle so that they taper (just like stems would in real life!). Pull chopstick out, add a drop of hot glue inside hole, place chopsticks back into holes. You now have a handle!

3. Place bald bouquet in tall vase/bottle. (This serves as a mobile pedestal and makes life so much easier when layering on paper and flowers.)

4. Tear the base color tissue paper into small rectangles, about 1x2 in size. Per the experimental prototype, we used a rich, blood red color because it matched the shadows under the paper roses. This will help hide any gaps between the paper roses as well.

5. Paint a 3x4 area on the styrofoam ball. Place slices of tissue paper on this area and brush the glue solution on top. (It’s just like paper mache or decopage!) Keep painting new areas on the foam ball and layering tissue paper like shingles. Be sure to do the same on the flat underside as well. Please note: These will take a few hours to dry because the tissue paper is like a sponge when it comes to the gluey goodness. But that’s why we do this first and move on to making roses next!

6. Get your rose-making engines started! That is, heat up the glue gun, grab some scissors, and cut out lots of circles from 3 to 5 inches in diameter. (Please note: You can follow my words below, or head to this awesome tutorial filled with great visuals.) Once you have all your circles ready, cut a spiral from outside to center, leaving a small circle about the size of a quarter in the middle. Using the end of a paintbrush or pen, roll from the outside in. When you get to the center, let go and see where the “petals” land. Bend the curled paper out of the way and run a few lines of hot glue across that small circle in the center (the base). Press the curled spiral down onto the glue and hold for a few seconds.

7. When your shingled styrofoam lollypop is dry, grab the glue gun and start placing roses all around the ball. Nestle them close together like they’re best buds about to hug. This snuggling of roses will help avoid large gaps in between.Also, for those closest to the base, allow the roses to hang off the edge a bit to hide the raw shape of the styrofoam.

Modeled stems ready for overnight drying.

8. Open up the package of Crayola Model Magic and tear off about half of it. Using your hands, roll it into a long snake. Press the modeling foam into the armature of the handle (stem) and begin to fill the center up. Wrap the foam around the outside (you may need to create a flat “pancake snake”) to cover any remaining bits of chopsticks. At this point you can mold the handle into your hands and make the shape more ergonomic. Let dry overnight.

9. Once the handle is dry (use a hair dryer the next day if it feels damp), grab your spool of ribbon. Starting at the base (on the styrofoam), about a half inch from the handle, glue the end of your first strip of ribbon. Wind it around WITHOUT gluing first, just to see how and where you’ll need to apply glue. Wrap the ribbon around as far as you can, and when you get to the very tip of where the chopsticks taper, allow the ribbon to fold over to help cover the raw ends. Work your way around the handle from the base and up, like a May Pole, until 100% covered.

10. Recreate the glue/water solution one last time. Take the remaining shingles of tissue paper and brush them over the funky glued edges of the ribbon. Work your way around to create a finished look on the underside. Let dry for a few hours.


Finishing Touches

The bridesmaids and I felt like the addition of large pearl beads in the center added a sophisticated touch the bouquets (it also hid any globs of hot glue). We used one package of large pearl bead mix from Michaels per bouquet. Depending on the size of your flowers, you may need smaller beads or love the largest size. Either way, Michaels’ beading section of the store has a ton of options, but certainly look for the inexpensive (and very lightweight) packages of pearls.

Last Step!

“Dust” the paper bouquet and remove all strings left over from the hot glue. It’s a pain, but once it’s done, your masterpiece is COMPLETE!

Field Notes

Time Required: 2 days (You can certainly make them over the course of a weekend)

Cost: NOTE: Outside of the foam ball and model magic, all other materials will be more than enough for you to create at least two, if not three bouquets.

Canson Flat Color Paper (assorted sheets): $6* Foam Ball: $6 Model Magic: $4 Tissue Paper: $2 Glue Sticks: $3 Elmers Glue: $2 Cheap Paint Brush: $2 Pearls: $4 Ribbon: $3 — — — — — — — — — — — — — — — — — — — — — — — - Total = $32**

F O O T N O T E S *See my previous post for why handpainted paper is worth mixing in with Canson paper. Pro tip: Purchase a Watercolor Board Pad for about $10.
**Don’t forget the most important investment: 1 Asian dinner with friends (for free chopsticks of course!)